Mighty-mule FM700 Manuel d'utilisateur

©2000 GTO, Inc.RB901 rev - 11/05/02Installation Manualfor theAutomatic Gate Opener SystemFOR SINGLE SWING GATESWARNING!This equipment is similar t

6IMPORTANT SAFETY INSTRUCTIONSInstall Warning SignsEntrapment ProtectionGTO’s inherent obstruction settings, even when properly adjusted, may not be s

7IMPORTANT SAFETY INSTRUCTIONSThese warning labels should be found at the locations specified below. If any of them are missing, immediately contact

8Single Gate Opener Parts ListOpener and Mounting HardwareSee Installation of the Post Bracket Assemblypages 5 and 6 in the Installation ManualHairpi

9Tools Needed• Power Drill• Open End Wrenches — 3/8", 7/16", 1/2", and 9/16"• 3/8" Drill Bit• Hacksaw or Heavy Duty Bolt Cutt

10DRIVE• Low friction screw drive (linear actuator) rated for -20 ºF to +160 ºF (-28 ºC to +71 ºC).• Powered by a 12 V motor with integral case harden

11 Horizontal Cross MemberGate Swings Evenly and FreelyHung Firmly and PlumbReceiverPost Bracket AssemblyControl Box with Battery Gate BracketSingle G

12Installation of Mounting HardwareThe position of the post bracket determines the leverage and efficiency of the opener. The post bracket position a

13Clevis PinHairpin ClipPost Bracket AssemblyOpenerWasherRear MountClevis PinHairpin ClipWasherGate BracketFront MountDetermining the Mounting Positio

14Step 6Study the 4 1/2" x 4 1/2" setback template (see insert) provided with this manual. Once you are familiar with itsillustrations, cut

15Installing the Post Bracket Assembly and Gate BracketStep 7Mark reference points for bolt holes on the fence post through middle of bracket slots.

VEHICULAR GATE OPENER CLASS CATEGORIESResidential Vehicular Gate Opener-Class I: A vehicular gate opener (or system) intended for use in a home ofone-

16Mounting the OpenerStep 11Attach the opener to the securely bolted post bracket assembly and gate bracket using clevis pins, washers, and hairpin cl

17At this stage of the installation, the opener should be installed on thegate and the open and closed position stops should be in place.Check List• T

18Step 15Make sure the control box power switch is in the OFFposition. Unscrew and remove the control box cover andslide the battery into position wi

19Step 17Carefully insert the power cableplug into the coupling at therear of the opener. Turn theplug until it aligns with the pinsin the coupling.

20Powering the SystemInstallation of the TransformerIMPORTANT:• The transformer is designed and intended for indoor use. If the transformer can be pl

21Step 23Lay the measured length of low voltage wire in atrench following a path from the selected electricaloutlet to the control box. Wires coming

22Step 27Plug the transformer into the electrical outlet.(Use of a surge protector with the transformer is stronglyrecommended.)HINT: Keep a few mothb

23The four DIP switches on the control board match the opener with the type of gate on which it isinstalled. For example, gates may pull-to-open or p

24PotentiometersThe three (3) potentiometers on the control board operate like a volume control on a radio. They controlthe auto close timer, inertia

252. Set the transmitter DIP SwitchesThere are nine (9) transmitter DIP switches; each can be placed in three different positions (+, 0, –). DO NOT

Gate Opener Class Categories -------------------------------------------------------------inside coverUnits and Standards Conversion Chart -----------

263. “Teach” the New Code to Control Board MemoryA. Turn control box power switch OFF.B. Unscrew and remove the control box cover.C. Press and ho

27ONSECOND OPERATORFIRST OPERATORPOWER IN ALARM ACCESSORY RCVRSEQ1SEQ2LEARN18VAC SOLAR~~ – +REDBLKORGBLUGRNCLS EDGOPN EDGREDBLKBLUORGORGBLUWHTGRNGRNCL

28Connecting AccessoriesThe ACCESSORY terminal block is the connection point for accessories such as keypads, push buttons, safety loops,intercoms, et

29Determining The Mounting Positionof The Post Bracket AssemblyStep PTO-1:With the gate closed, adjust the post bracket assembly and the gatebracket u

30OperatorFence PostGate Post and Gate Cross Member (In Closed Position)POST PIVOT BRACKET level with the horizontal surface of the GATE

31Maintenance & Troubleshooting GuideIf your gate opener does not function properly after it is installed, use this guide before calling the GTO S

32The Gate CLOSES Then Opens Again on its Own:1. Check the position of the mounting brackets and readjust if necessary.2. Check the gate for binding o

33If your Mighty Mule Gate Opener® is not operating properly, please follow the steps below:1. First use the procedures found in the Maintenance &

34Column Installation InformationIF THIS OPENER WILL BE USED WITH GATES THAT ARE MOUNTED ONMASONRY, BRICK, OR ROCK (etc.) COLUMNS:READ THE FOLLOWING C

35Accessory CatalogAUTOMATIC GATE OPENER

PLEASE READ THIS FIRST!iiiBEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPENER:watch the enclosed videotape and read these instructions carefully an

36Pin Lock (FM133)The Pin Lock substitutes for the clevispin at the front mounting point of theopener. Helps prevent theft of the openerfrom the gat

37The Following Accessories Are Available Through YourRetail Store's Special Order Desk.Dual Transmitter (RB742)The Dual Transmitter is a two but

38GTO, Inc.For sales call toll free:1-800-543-GATEFor technical service Call toll free:1-800-543-1236Mighty Mule® Limited One Year Warranty:GTO, Inc.,

1IMPORTANT SAFETY INSTRUCTIONSBecause automatic gate openers produce high levels of force, consumers need to know the potential hazards associated wit

2IMPORTANT SAFETY INSTRUCTIONSFor The ConsumerWARNING: To reduce the risk of injury or death:1. READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the

3IMPORTANT SAFETY INSTRUCTIONSEntrapment Zones:Zone 1 – leading edge of the gate and the fence post.Zone 2 – between the gate and the gate postZone 3

4IMPORTANT SAFETY INSTRUCTIONSIII. After Installation1. Attach the warning signs (included) to each side of the gate to alert the public of automatic

5IMPORTANT SAFETY INSTRUCTIONSENTRAPMENT ALARM (UL 325; 30A.1.1A)The Mighty Mule E-Z Gate Opener is designed to stop and reverse within 2 seconds whe