Mighty-mule FM137 Manuel d'utilisateur télécharger pdf (Page 4)

Step 2: Strip the wires back 3/16” and attach the wires to the terminal block marked OUT COM on

the keypad control board as shown in (FIG. 7) making sure to keep track of polarity. Connect

the other end to the opener’s control board as shown in Control Board Connections section

below.

NOTE: For a hard-wired application the 318 MHz RF transmitter is automatically disabled.

Step 3: With the power to the opener turned OFF. Remove opener

control board cover and feed enough of the low voltage keypad

wire through a strain relief to reach the gate opener control board

terminals.

Step 4: Attach the wires from the keypad to the opener control board

terminal blocks as shown below. (FIG. 9)

Step 5: Replace the control board cover and turn the power switch

ON. Put the batteries back into the keypad. (FIG. 2) Test the

keypad by entering to open gate.

Step 6: Program new “Personal Master Code” and any additional entry codes

(for a total of 25 entry codes) (if desired). See Program the Keypad on page 5.

Step 7: Slide the keypad into the cover and secure with the small screws provided. (FIG. 8)

OUT COM

Hard-wire from Gate Opener

ABC

DEF

GHI

JKL

MNO

PRS

TUV

WXY

Connect #1 wire from the

OUT terminal on the keypad

to the CYCLE terminal on the

opener control board.

Connect #2 wire

from the COM terminal on the

keypad to COM terminal on

the opener control board.

POWER

CHGR

EDGE

CYCLE

EXIT

SAFETY

COM

LOCK+

LOCK -

Mighty Mule 200 Control Board

Control Board Connection Examples

NOTE: If your control board doesn’t look like any of these diagrams, please refer to the opener’s instruction manual to locate

the control board input.

RECR

GRN

BLK

RED

EXIT

SAFETY

EDGE

CYCLE

COMMON

LINK

Mighty Mule 350 Control Board

Connect #1 wire from the

OUT terminal on the keypad

to CYCLE terminal on the

gate opener control board.

Connect #2 wire from the COM

terminal on the keypad to the

COMMMON terminal on the gate

opener control board.

RECEIVER

ALM

GTO RCVR.

COM

GRN

BLK

RED

CYCLE

SAFETY

EXIT

SHADOW

OPEN

EDGE

COM

CONTROL INPUTS

EDGE

Connect the #1 wire from

the OUT terminal on the keypad to

the CYCLE terminal on the opener

control board.

Connect the #2 wire from the

COM terminal on the keypad

to one of the COM terminals

on the opener control board.

GEN-3 (Blue) Control Boards

GTO/PRO GP-SL100 and GP-SW100

Control Boards

COM

GTO Inc.

SX4000 L

CYCLE

SAFETY

OPEN EDGE

RUN 2

OPEN

STOP

COM

SHADOW

LOOP

Connect the #1 wire from

the OUT terminal on the

keypad to the CYCLE

terminal on the opener

control board.

Connect the #2 wire from the

COM terminal on the keypad

to one of the COM terminals

on the opener control board.

VAR5

PF1

BATT +

VAR4

VAR3

VAR2

VAR1

PWR.

SFTY.

EXIT

CYCLE

EDGE

SENSOR

COMMON

LOCK+

LOCK–

WHT

GRN

RED

BLK

WHT

GRN

SECOND OPR.FIRST OPR.

RED

BLK

14 VAC

SOLAR

Connect #1 wire from the

OUT terminal on the keypad

to the CYCLE terminal on

the opener control board.

Connect #2 wire from the

COM terminal on the keypad

to COMMON terminal on the

opener control board.

Mighty Mule 362/402

PRO-SW2000XLS

Control Board

ALARM ACCESSORY RCVR

SEQ1

SEQ2

LEARN

BLU

ORG

WHT

GRN

R B G

Connect #1 wire from the

OUT

terminal on the keypad

to the WHT terminal on the

opener control board.

Connect #2 wire

from the COM terminal on the

keypad to GRN terminal on

the opener control board.

PRO-1000, PRO-SL1000 and Old Mighty Mule

Control Boards

Wired Installation of the Keypad

IMPORTANT: Remove the batteries from the keypad. The keypad will not work properly if

batteries are not ﬁrst removed.

Step 1: Turn the gate opener’s power switch OFF. Run wire through PVC pipe between the opener

control board to protect the wire.

Remove the small rectangular knock-out on the back of the keypad cover and pull the wire into the

cover. Then mount the cover to the post using the screws provided. (FIG. 6)

Knock-out

FIG. 6

FIG. 7

FIG. 8

FIG. 9

1 2 3 4

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Mighty-mule FM137 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Mighty-mule FM137